Stages of design development GOST 2.103
GOST 2.103-2013
INTERSTATE STANDARD
Unified system for design documentation
DEVELOPMENT STAGES
Unified system for design documentation Stages of designing
For the text of Comparison of GOST 2.103-2013 with GOST 2.103-68, see the link.
- .
____________________________________________________________________
ISS 01.110
OKSTU 0002
Introduction date 2015-07-01
Foreword
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 "Interstate standardization system. Basic provisions" and GOST 1.2-2009 "Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. Rules for development, adoption, application, renewal and cancellation "
Information about the standard
1 DEVELOPED by the Federal State Unitary Enterprise "All-Russian Scientific Research Institute of Standardization and Certification in Mechanical Engineering" (VNIINMASH), Autonomous non-profit organization Research Center for CALS Technologies "Applied Logistics" (ANO Research Center for CALS Technologies "Applied Logistics")
2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology
3 ACCEPTED by the Interstate Council for Standardization, Metrology and Certification (minutes of November 14, 2013 N 44, Appendix N 24 add.)
4 By Order Federal agency on technical regulation and metrology of November 26, 2014 N 1794-st, the interstate standard GOST 2.103-2013 was put into effect as a national standard Russian Federation since 01 July 2015
5 REPLACE GOST 2.103-68
6 SECOND EDITION (April 2015) as amended, published in IMS No. 7 2015
Information on changes to this standard is published in the annual information index "National Standards", and the text of changes and amendments is published in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, the corresponding notice will be published in the monthly information index "National Standards". Relevant information, notice and texts are also posted in information system general use - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet
Corrected by the manufacturer of the database
1 area of \u200b\u200buse
1 area of \u200b\u200buse
This standard specifies the stages of development of design documentation for products of all industries and stages of work.
On the basis of this standard, standards can be developed that take into account the peculiarities of the application of the stages of development of design documentation at various stages of the product life cycle. specific types technology depending on the specifics of their development, production and use.
2 Normative references
This standard uses normative references to the following interstate standards:
GOST 2.002-72 Unified system for design documentation. Requirements for models, layouts and templates used in design
GOST 2.052-2006 Unified system for design documentation. Electronic model of the product. General Provisions
GOST 2.053-2013 Unified system for design documentation. Electronic structure of the product. General Provisions
GOST 2.102-2013 Unified system for design documentation. Types and completeness of design documents
GOST 2.118-2013 Unified system for design documentation. Technical Proposal
GOST 2.119-2013 Unified system for design documentation. Preliminary design
GOST 2.120-2013 Unified system for design documentation. Technical project
GOST 2.125-2008 Unified system for design documentation. Rules for the execution of sketch design documents. General Provisions
GOST 2.601-2013 Unified system for design documentation. Operational documents
GOST 2.602-2013 Unified system for design documentation. Repair documents
Note - When using this standard, it is advisable to check the validity of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or according to the annual information index "National Standards", which was published as of January 1 of the current year, and by releases of the monthly information index "National Standards" for the current year. If the reference standard is replaced (changed), then when using this standard, the replacing (modified) standard should be followed. If the reference standard is canceled without replacement, then the provision in which the reference to it is given applies to the extent not affecting this reference.
3 Terms, definitions and abbreviations
3.1 Terms and definitions
The following terms are used in this standard with the corresponding definitions:
3.1.2 letter: Details of the design document (set of design documents) for the product corresponding to the stage of its development.
3.1.4 pilot batch: A set of prototypes or a certain volume of non-piece products, manufactured for a specified time interval according to the newly developed one and the same documentation to control the compliance of products with specified requirements and make a decision on putting it into production.
3.1.5 project design documentation: Design documentation completed at the stages of a technical proposal, draft and technical design.
3.1.6 working design documentation: Design documentation, executed at the stages of a prototype (pilot batch) of serial (mass) and single production and intended for the manufacture, operation, repair (modernization) and disposal of the product.
3.1.7 stage of development of design documentation: The finished part of the design documentation development process, consisting of stages of work and characterized by the achievement of a given result.
3.1.8 installation series: The first industrial batch of products manufactured during the period of mastering production according to the documentation of serial or mass production in order to confirm the readiness of production to release products with the established requirements and in the specified volumes.
3.2 Abbreviations
The following abbreviations are adopted in this standard:
КД - design documents (documents, documentation);
TK - technical task.
4 Key points
4.1 The stages of design documentation development can be performed in the form of design and working design documentation development. The stages of development of design documentation and the stages of performance of work established by this standard are shown in Table 1.
Table 1
Development stage | ||
The “Technical Proposal” stage does not apply to design documents developed * by order of the Ministry of Defense. Note - All stages of development of a working design documentation may be preceded by the stage of development of a design design document. |
__________
* The text of the document corresponds to the original. -.
Table 1. (Amendment. IMS N 10-2016).
4.2 The nomenclature of types of documents developed at each stage of development of design documentation - in accordance with GOST 2.102, if the composition of the documentation is not established in the TOR for development.
4.3 The obligation to complete the development stages and stages of work, the form for submitting the design documentation (paper and (or) electronic) should be established by the developer, if this is not established in the TOR for development.
4.4 If one of the development stages inherent in development work is not completed, the work related to these stages must be carried out at one of the development stages being performed.
4.5 Requirements for the implementation of CA must meet the requirements Unified system design documentation.
4.6 The need to develop layouts, their type, conditions and test (analysis) programs, as well as the need to develop documentation for the manufacture and testing of layouts should be established by the developer, if this is not established in the TOR for development. Layouts can be made in material form (material layout) or virtual form (electronic layout). Requirements for the material model in accordance with GOST 2.002, for the electronic model - in accordance with GOST 2.052.
Material layouts should be made, as a rule, according to sketch design documentation, in accordance with GOST 2.125 *.
_______________
Here and below, the "*" marks the items to which the comments are given in Appendix A.
4.7 When performing electronic CA, it is recommended to establish requirements for data formats at a previous stage of development, if this is not established by the TOR.
4.8 When performing electronic CD, the electronic structure of the product and the electronic model of the product (assembly unit, complex, kit) should be performed with a degree of detail corresponding to the development stage. Requirements for the electronic model of the product - in accordance with GOST 2.052, for the electronic structure of the product - in accordance with GOST 2.053.
4.9 Working design documentation for products of a single production may be preceded by the performance of design documentation for individual stages of development (technical proposal, conceptual design, technical design) and, accordingly, the stages of the work indicated in Table 1.
4.10 Technical proposal - a set of design design documents, which must contain technical and feasibility studies for the feasibility of developing product documentation based on the analysis of technical specifications and various options for possible product solutions, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products, as well as patent research ...
A technical proposal after agreement and approval in the prescribed manner is the basis for the development of a draft (technical) design.
List of works - according to GOST 2.118.
4.11 Draft design - a set of design design documents, which should contain fundamental design solutions that give a general idea of \u200b\u200bthe purpose, device, principle of operation and overall dimensions of the product being developed, as well as data that determine its main parameters.
The draft design, after agreement and approval in the prescribed manner, serves as the basis for the development of a technical design or working design document.
List of works - according to GOST 2.119.
4.12 Technical design - a set of design design documentation, which must contain the final technical solutions that give a complete picture of the device being developed, and the initial data for the development of a working design documentation.
The technical project, after agreement and approval in the prescribed manner, serves as the basis for the development of a working design document.
List of works - according to GOST 2.120.
4.13 Previously developed design documentation should be used in the development of new or modernization of manufactured products in the following cases:
a) in the project design documentation (technical proposal, draft and technical projects);
b) in the working CD with the letters "", "" ("", "", ... ""), "A", "B" and "I", if the lettering of the document used is the same or higher.
The lettering of a complete set of design documents is determined by the lowest of the letters specified in the design documentation included in the kit, except for the design documentation of purchased products.
4.14 CA, the originals of which are held by other organizations, can be used in the organization only if there are registered copies or duplicates of these CAs.
4.15 At the stages of development, "Development of the design design document" should be developed for the design design document.
At the stages "Development of a working design document", a working design document should be developed.
Working design documentation transferred (supplied) to the manufacturer for the production of products includes, among other things, operational documentation made in accordance with GOST 2.601, which is then supplied to the consumer (operator) along with the product. The design and operational design documentation should be developed at the stage of the product life cycle "Design (development)".
Repair design documentation, if necessary, should be developed in accordance with GOST 2.602 at the stage of the product life cycle "Repair", as a rule, after a certain period of product operation *.
Appendix A (reference). Comments on the clauses of the standard
Appendix A
(reference)
4.6 An electronic model is a collection of electronic models of a product that describes it external shape and dimensions that allow to fully or partially evaluate its interaction with elements of the production and / or operational environment, which serves to make decisions in the development of a product and the processes of its manufacture and use.
An electronic model is a virtual image of a product or an imitation reproduction of specific properties of a created product or its component part, which allows to fully or partially investigate individual characteristics of the product, as well as to evaluate the correctness of the adopted technical and design solutions.
Material and electronic layouts should be developed:
a) at the stage of developing a technical proposal in order to identify and check options for the main design solutions of the product being developed or its components, analyze various product options, identify additional or clarified requirements for the product;
b) at the stage of development of a draft design in order to check the principles of operation of the product or its component parts, the conditions for placement in the allotted space, the conditions of ergonomics of use and other properties of the product or its component parts;
c) at the stage of development of a technical project in order to check the basic design solutions of the product being developed or its components in terms of spatial-kinematic interaction with other products and component parts with each other and ergonomic conditions;
d) at the stage of developing a working design document for preliminary verification of the feasibility of changing individual components of the manufactured product before making these changes to the working design document of a prototype (pilot batch).
4.15 Life cycle products, as a rule, consists of the following stages: marketing-scientific research, design (development), manufacture, control (acceptance), operation, repair, disposal.
Electronic text of the document
and verified by:
official publication
M .: Standartinform, 2015
Document revision taking into account
changes and additions prepared
INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION
INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATION
INTERSTATE
STANDARD
Official edition
Standardinform
Foreword
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions "and GOST 1.2-2009" Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. Rules for development, acceptance, application, updating and cancellation "
Information about the standard
1 DEVELOPED by the Federal State Unitary Enterprise "All-Russian Research Institute of Standardization and Certification in Mechanical Engineering" (VNIINMASH), the Autonomous Non-Profit Organization Research Center of CALS-Technologies "Applied Logistics" (ANO Research Center of CALS-Technologies "Applied Logistics")
2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology
3 ACCEPTED by the Interstate Council for Standardization, Metrology and Certification (Minutes of November 14, 2013 Nv 44, Appendix Ns\u003e 24 add.)
| Short name of the country no MK (ISO 3166) 004-97 |
Country code according to MK (ISO 3166) 004-97 |
Abbreviated name of the national standardization body |
| Azerbaijan |
Azstandard |
|
| Ministry of Economy of the Republic of Armenia |
||
| Belarus |
Gosstandart of the Republic of Belarus |
|
| Kazakhstan |
Gosstandart of the Republic of Kazakhstan |
|
| Kyrgyzstan |
Kyrgyzstandard |
|
| Moldova-Standard |
||
| Rosstandart |
||
| Tajikistan |
Tajikstandart |
|
| Uzbekistan |
Uzstandart |
|
| State Consumer Standards of Ukraine |
4 By order of the Federal Agency for Technical Regulation and Metrology dated November 26, 2014 No. 1794-st, the interstate standard GOST 2.103-2013 was put into effect as a national standard of the Russian Federation from July 1, 2015.
6 SECOND EDITION (April 2015) as amended, published in IMS No. 7 2015
Information about changes to this standard is published in the annual information index "National standards". and the text of changes and amendments is in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, a corresponding notice will be published in the monthly information index "National Standards". Relevant information, notice and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet
© Standartinform, 2015
In the Russian Federation, this standard cannot be fully or partially reproduced, replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology.
INTERSTATE
GOST 2.103-2013
STANDARD
Unified system for design documentation DEVELOPMENT STAGE
Unified system for design documentation Stages of designing
Introduction date - 2015-07-01
1 area of \u200b\u200buse
This standard specifies the stages of development of design documentation for products of all industries and stages of work.
On the basis of this standard, standards can be developed that take into account the peculiarities of the application of the stages of development of design documentation at various stages of the product life cycle of specific types of equipment, depending on the specifics of their development, production and use.
This standard uses normative references to the following interstate standards:
GOST 2.002-72 Unified system for design documentation. Requirements for models, layouts and templates used in design
GOST 2.052-2006 Unified system for design documentation. Electronic model of the product. General Provisions
GOST 2.053-2013 Unified system for design documentation. Electronic structure of the product. General Provisions
GOST 2.102-2013 Unified system for design documentation. Types and completeness of design documents
GOST 2.118-203. Unified system for design documentation. Technical proposal GOST 2.119-2013 Unified system for design documentation. Draft design GOST 2.120-2013 Unified system for design documentation. Technical project GOST 2.125-2008 Unified system for design documentation. Rules for the execution of sketch design documents. General Provisions
GOST 2.601-2013 Unified system for design documentation. Operational documents
GOST 2.602-2013 Unified system for design documentation. Repair documents
Note - When using this standard, it is advisable to check the validity of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or according to the annual information index "National Standards", which was published as of January 1 of the current year, and on the issues of the monthly information index "National Standards" for the current year. If the reference standard is replaced (changed), then when using this standard, the replacing (modified) standard should be followed. If the reference standard is canceled without replacement, then the provision in which the reference to it is given applies to the extent not affecting this reference.
3 Terms, definitions and abbreviations
3.1 Terms and definitions
The following terms are used in this standard with the corresponding definitions:
Official edition
3.1.1 one-off production: A production characterized by a low volume of production of identical products, the re-production and repair of which, as a rule, is not provided.
__ [GOST 14.004-83. paragraph 20]
3.1.2 letter: Details of the design document (set of design documents) on
product corresponding to the stage of its development.
3.1.3 prototype: A sample of the product made according to the newly developed working documentation for verification by testing its compliance with the specified technical requirements in order to make a decision on the possibility of putting into production and (or) use for its intended purpose.
_ [GOST 16504-81, art. eight]
3.1.4 pilot batch: A set of prototypes or a certain volume of non-piece products manufactured for a specified time interval according to the newly developed one and the same documentation to control the conformity of products to specified requirements and make a decision on putting it into production.
3.1.5 design design documentation: design documentation,
executed at the stages of technical proposal, draft and technical projects.
3.1.6 working design documentation: Design documentation executed at the stages of a prototype (pilot batch) of serial (mass) and single production and intended for the manufacture, operation, repair (modernization) and disposal of the product.
3.1.7 design documentation development stage: The finished part of the design documentation development process, consisting of stages of work and characterized by the achievement of a given result.
3.1.8 installation series: The first industrial batch of products manufactured during
mastering production according to the documentation of serial or mass production in order to confirm the readiness of production to release products with the established requirements and in the specified volumes._
3.1.9 data format: The order in which the data symbols are arranged so that their constituent parts can be recognized.
NOTE - The data format takes on a variation depending on the particular set of data symbols, for example the format of the data message.
[GOST 17657-79. Appendix, paragraph 11]
3.2 Abbreviations
The following abbreviations are adopted in this standard:
КД - design documents (documents, documentation);
TK - technical task.
4 Key points
4.1 The stages of design documentation development can be performed in the form of design and working design documentation development.
The stages of development of design documentation and the stages of performance of work established by this standard are shown in Table 1.
Table 1
| Development stage |
Stages of work |
|
| Development of design design documentation |
Development of a technical proposal * " |
Study and analysis of TK |
| Selection of materials |
||
| Development of design documentation for a technical proposal. |
||
| Consideration and approval of the CA of the technical proposal with the assignment of the CA letter VP " |
||
| Development of a draft design |
Development of a draft design |
|
| Manufacturing and testing and / or development and analysis of material layouts (if necessary) and (or) development, analysis of electronic layouts (if necessary) |
||
| Consideration and approval of the design documentation of the draft design with the assignment of the letter "E" to the documents |
||
GOST 2.103-2013
End of table 1
| Development stage |
Stages of work |
|
| Development design |
Development of a technical project |
|
| Production and testing of material layouts (if necessary) and / or development, analysis of electronic layouts (if necessary) |
||
| Consideration and approval of the design documentation of the technical project with the assignment of the design document letter * T " |
||
| Development |
Development of design documentation for a prototype (pilot batch) product |
Development of design documentation. intended for the manufacture and testing of a prototype (pilot batch) of a product, without assigning a letter |
| Manufacturing and preliminary testing of a prototype (pilot batch) product |
||
| Correction of design documentation based on the results of manufacturing and preliminary tests of a prototype (pilot batch) of the product with the assignment of design documentation letter "O" |
||
| Acceptance tests of a prototype (pilot batch) of a product |
||
| Correction of design documentation based on the results of acceptance tests of a prototype (pilot batch) of the product with the assignment of design documentation letter "Oi" |
||
| For a product developed by order of the Ministry of Defense, if necessary, re-manufacturing and testing of a prototype (pilot batch) according to documentation with the letter "Oi" and adjusting the design documentation with the assignment of the letter "Og *. Oz. ... "0" * |
||
| Development of design documentation for a serial (mass) product |
Manufacturing and testing of the installation series according to the documentation with the letter "Oi" (or "Og". "Oj", ... "O n") |
|
| Correction of design documentation based on the results of manufacturing and testing of the installation series, as well as equipping the technological process of manufacturing a product, with the assignment of design documentation letter "A" |
||
| For a product developed by order of the Ministry of Defense, if necessary, the production and testing of the lead (control) series of design documents with the letter "A" and the corresponding correction of the design documents with the assignment of the letter "B" |
||
| Development of design documentation for a single-piece product |
Development of design documentation. intended for the manufacture and testing of the product with the assignment of the letter "I" |
|
| ”Stage“ Technical proposal ”does not apply to CA. developed by order of the Ministry of Defense. Note - All stages of development of a working design documentation may be preceded by the stage of development of a design design document. |
||
4.2 The nomenclature of types of documents developed at each stage of development of design documentation - according to GOST 2.102. if the composition of the documentation is not established in the TOR for development.
4.3 The obligation to complete the development stages and stages of work, the form for submitting the design documentation (paper and (or) electronic) should be established by the developer, if this is not established in the TOR for development.
4.4 If one of the development stages inherent in development work is not completed, the work related to these stages must be carried out at one of the development stages being performed.
4.5 Requirements for the implementation of design documentation must comply with the requirements of the Unified System for Design Documentation.
4.6 The need to develop layouts, their appearance. the conditions and programs of tests (analysis), as well as the need for the development of documentation for the manufacture and testing of models should be established by the developer, if this is not established in the TOR for development. Layouts can be made in material form (material layout) or virtual form (electronic layout). Requirements for the material model according to GOST 2.002. to the electronic model - according to GOST 2.052.
Material layouts should be made, as a rule, according to sketch design documentation. in accordance with
4.7 When performing electronic CA, it is recommended to establish requirements for data formats at a previous stage of development, if this is not established by the TOR.
4.8 When performing electronic CD, the electronic structure of the product and the electronic model of the product (assembly unit, complex, kit) should be performed with a degree of detail corresponding to the development stage. Requirements for the electronic model of the product are in accordance with GOST 2.052. to the electronic structure of the product - according to GOST 2.053.
4.9 Working design documentation for products of a single production may be preceded by the performance of design documentation for individual stages of development (technical proposal, conceptual design, technical design) and, accordingly, the stages of the work indicated in Table 1.
4.10 Technical proposal - a set of project design documentation. which should contain technical and feasibility studies for the feasibility of developing product documentation based on the analysis of technical specifications and various options for possible solutions for products, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products, as well as patent research.
A technical proposal after agreement and approval in the prescribed manner is the basis for the development of a draft (technical) design.
List of works - according to GOST 2.118.
4.11 Draft design - a set of design design documentation. which should contain fundamental design solutions that give a general idea of \u200b\u200bthe purpose, device, principle of operation and overall dimensions of the product being developed, as well as data defining its main parameters.
The draft design, after agreement and approval in the prescribed manner, serves as the basis for the development of a technical design or working design document.
List of works - according to GOST 2.119.
4.12 Technical design is a set of design documentation. which should contain the final technical solutions that give a complete picture of the device under development, and the initial data for the development of a working design documentation.
The technical project, after agreement and approval in the prescribed manner, serves as the basis for the development of a working design document.
List of works - according to GOST 2.120.
4.13 Previously developed design documentation should be used in the development of new or modernization of manufactured products in the following cases:
a) in the project design documentation (technical proposal, draft and technical projects);
b) in the working CD with the letters "O". "O," ("O g", "0 3", ... "O n"), "A", "B" and "I", if the lettering of the document used is the same or higher.
The lettering of the complete set of CD is determined by the lowest of the letters indicated in the CD. included in the kit, except for the CD of purchased products.
4.14 CD. holders of originals of which are other organizations can be used in the organization only if there are registered copies or duplicates of these CDs.
4.15 At the stages of development, "Development of the design documentation" should be developed for the design
At the stages "Development of a working design document", a working design document should be developed.
Working CD. transferred (supplied) to the manufacturing organization for the production of products includes, among other things, operational documentation made in accordance with GOST 2.601. which is then supplied to the consumer (operator) along with the product. The design and working design documentation should be developed at the stage of the product life cycle "Design (development)".
Repair CD. if necessary, it should be developed in accordance with GOST 2.602 at the stage of the product life cycle "Repair", as a rule, after a certain period of operation of the product *.
GOST 2.103-2013
Appendix A (informative)
page 1
page 2
page 3
p. 4
p. 5
page 6
page 7
page 8
page 9
page 10
INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION
INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION
INTERSTATE
STANDARD
GOST 2.103-2013
2013
Unified system for design documentation DEVELOPMENT STAGES
Official edition
|
Standardinform ForewordThe goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions "and GOST 1.2-2009" Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. Rules for development, acceptance, application, updating and cancellation " Information about the standard 1 DEVELOPED by the Federal State Unitary Enterprise "All-Russian Research Institute of Standardization and Certification in Mechanical Engineering" (VNIINMASH), the Autonomous Non-Profit Organization Research Center of CALS-Technologies "Applied Logistics" (ANO Research Center of CALS-Technologies "Applied Logistics") 2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology 3 ACCEPTED by the Interstate Council for Standardization, Metrology and Certification (Minutes of November 14, 2013 No. 44, Appendix No. 24 add.)
4 By order of the Federal Agency for Technical Regulation and Metrology of November 26, 2014 No. 1794-st, the interstate standard GOST 2.103-2013 was put into effect as a national standard of the Russian Federation from July 1, 2015. 6 SECOND EDITION (April 2015) as amended, published in IMS No. 7 2015 Information about changes to this standard is published in the annual information index "National Standards", and the text of changes and amendments is published in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, the corresponding notice will be published in the monthly information index "National standards". Relevant information, notice and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet © Standartinform, 2015 In the Russian Federation, this standard cannot be fully or partially reproduced, replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology. |
||||||||||||||||||||||||||||||||||||
|
(ICS No. 7 2015) |
|
|||||||||
|
(ICS No. 10 2016) |
3.1.1 one-off production: A production characterized by a low volume of production of identical products, the re-production and repair of which, as a rule, is not provided.
|
End of table 1 |
|||||||||||||||||||||||||
|
|||||||||||||||||||||||||
4.2 The nomenclature of types of documents developed at each stage of development of design documentation - in accordance with GOST 2.102, if the composition of the documentation is not established in the TOR for development.
4.3 The obligation to complete the development stages and stages of work, the form for submitting the design documentation (paper and (or) electronic) should be established by the developer, if this is not established in the TOR for development.
4.4 If one of the development stages inherent in development work is not completed, the work related to these stages must be carried out at one of the development stages being performed.
4.5 Requirements for the implementation of design documentation must comply with the requirements of the Unified System for Design Documentation.
4.6 The need to develop layouts, their type, conditions and test (analysis) programs, as well as the need to develop documentation for the manufacture and testing of layouts should be established by the developer, if this is not established in the TOR for development. Layouts can be made in material form (material layout) or virtual form (electronic layout). Requirements for the material model in accordance with GOST 2.002, for the electronic model - in accordance with GOST 2.052.
Material layouts should be made, as a rule, according to sketch design documentation, in accordance with GOST 2.125 * 1 '.
4.7 When performing electronic CA, it is recommended to establish requirements for data formats at a previous stage of development, if this is not established by the TOR.
4.8 When performing electronic CD, the electronic structure of the product and the electronic model of the product (assembly unit, complex, kit) should be performed with a degree of detail corresponding to the development stage. Requirements for the electronic model of the product - in accordance with GOST 2.052, for the electronic structure of the product - in accordance with GOST 2.053.
4.9 Working design documentation for products of a single production may be preceded by the performance of design documentation for individual stages of development (technical proposal, conceptual design, technical design) and, accordingly, the stages of the work indicated in Table 1.
4.10 Technical proposal - a set of design design documents, which must contain technical and feasibility studies for the feasibility of developing product documentation based on the analysis of technical specifications and various options for possible product solutions, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products, as well as patent research ...
A technical proposal after agreement and approval in the prescribed manner is the basis for the development of a draft (technical) design.
4.11 Draft design - a set of design design documents, which should contain fundamental design solutions that give a general idea of \u200b\u200bthe purpose, device, principle of operation and overall dimensions of the product being developed, as well as data that determine its main parameters.
The draft design, after agreement and approval in the prescribed manner, serves as the basis for the development of a technical design or working design document.
4.12 Technical design - a set of design design documentation, which must contain the final technical solutions that give a complete picture of the device being developed, and the initial data for the development of a working design documentation.
The technical project, after agreement and approval in the prescribed manner, serves as the basis for the development of a working design document.
4.13 Previously developed design documentation should be used in the development of new or modernization of manufactured products in the following cases:
a) in the project design documentation (technical proposal, draft and technical projects);
b) in the working CD with the letters "O", "O ^ (" 0 2 "," O e ", ..." O n ")," A "," B "and" I ", if the lettering of the document used the same or higher.
The lettering of a complete set of design documents is determined by the lowest of the letters specified in the design documentation included in the kit, except for the design documentation of purchased products.
4.14 CA, the originals of which are held by other organizations, can be used in the organization only if there are registered copies or duplicates of these CAs.
4.15 At the stages of development, "Development of the design documentation" should be developed for the design
At the stages "Development of a working design document", a working design document should be developed.
The working design documentation transmitted (supplied) to the manufacturing organization for the production of products includes, among other things, operational documentation prepared in accordance with GOST 2.601, which is then supplied to the consumer (operator) along with the product. The design and working design documentation should be developed at the stage of the product life cycle " Design (development) ".
The repair design documentation, if necessary, should be developed in accordance with GOST 2.602 at the stage of the product life cycle "Repair", as a rule, after a certain service life of the product *.
INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION
INTERSTATE COUNCIL FOR STANDARDIZATION. METROLOGY AND CERTIFICATION
INTERSTATE
STANDARD
Official edition
Standardinform
Foreword
The goals, basic principles and basic procedure for carrying out work on interstate standardization are established by GOST 1.0-92 “Interstate standardization system. Basic provisions "and GOST 1.2-2009" Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. Rules for development, acceptance, application, updating and cancellation "
Information about the standard
1 DEVELOPED by the Federal State Unitary Enterprise "All-Russian Research Institute of Standardization and Certification in Mechanical Engineering" (VNIINMASH), the Autonomous Non-Profit Organization Research Center of CALS-Technologies "Applied Logistics" (ANO Research Center of CALS-Technologies "Applied Logistics")
2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology
3 ACCEPTED by the Interstate Council for Standardization, Metrology and Certification (Minutes of November 14, 2013 Nv 44, Appendix Ns\u003e 24 add.)
| Short name of the country no MK (ISO 3166) 004-97 |
Country code according to MK (ISO 3166) 004-97 |
Abbreviated name of the national standardization body |
| Azerbaijan |
Azstandard |
|
| Ministry of Economy of the Republic of Armenia |
||
| Belarus |
Gosstandart of the Republic of Belarus |
|
| Kazakhstan |
Gosstandart of the Republic of Kazakhstan |
|
| Kyrgyzstan |
Kyrgyzstandard |
|
| Moldova-Standard |
||
| Rosstandart |
||
| Tajikistan |
Tajikstandart |
|
| Uzbekistan |
Uzstandart |
|
| State Consumer Standards of Ukraine |
4 By order of the Federal Agency for Technical Regulation and Metrology dated November 26, 2014 No. 1794-st, the interstate standard GOST 2.103-2013 was put into effect as a national standard of the Russian Federation from July 1, 2015.
6 SECOND EDITION (April 2015) as amended, published in IMS No. 7 2015
Information about changes to this standard is published in the annual information index "National standards". and the text of changes and amendments is in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, a corresponding notice will be published in the monthly information index "National Standards". Relevant information, notice and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet
© Standartinform, 2015
In the Russian Federation, this standard cannot be fully or partially reproduced, replicated and distributed as an official publication without the permission of the Federal Agency for Technical Regulation and Metrology.
INTERSTATE
GOST 2.103-2013
STANDARD
Unified system for design documentation DEVELOPMENT STAGE
Unified system for design documentation Stages of designing
Introduction date - 2015-07-01
1 area of \u200b\u200buse
This standard specifies the stages of development of design documentation for products of all industries and stages of work.
On the basis of this standard, standards can be developed that take into account the peculiarities of the application of the stages of development of design documentation at various stages of the product life cycle of specific types of equipment, depending on the specifics of their development, production and use.
This standard uses normative references to the following interstate standards:
GOST 2.002-72 Unified system for design documentation. Requirements for models, layouts and templates used in design
GOST 2.052-2006 Unified system for design documentation. Electronic model of the product. General Provisions
GOST 2.053-2013 Unified system for design documentation. Electronic structure of the product. General Provisions
GOST 2.102-2013 Unified system for design documentation. Types and completeness of design documents
GOST 2.118-203. Unified system for design documentation. Technical proposal GOST 2.119-2013 Unified system for design documentation. Draft design GOST 2.120-2013 Unified system for design documentation. Technical project GOST 2.125-2008 Unified system for design documentation. Rules for the execution of sketch design documents. General Provisions
GOST 2.601-2013 Unified system for design documentation. Operational documents
GOST 2.602-2013 Unified system for design documentation. Repair documents
Note - When using this standard, it is advisable to check the validity of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or according to the annual information index "National Standards", which was published as of January 1 of the current year, and on the issues of the monthly information index "National Standards" for the current year. If the reference standard is replaced (changed), then when using this standard, the replacing (modified) standard should be followed. If the reference standard is canceled without replacement, then the provision in which the reference to it is given applies to the extent not affecting this reference.
3 Terms, definitions and abbreviations
3.1 Terms and definitions
The following terms are used in this standard with the corresponding definitions:
Official edition
3.1.1 one-off production: A production characterized by a low volume of production of identical products, the re-production and repair of which, as a rule, is not provided.
__ [GOST 14.004-83. paragraph 20]
3.1.2 letter: Details of the design document (set of design documents) on
product corresponding to the stage of its development.
3.1.3 prototype: A sample of a product made according to a newly developed working documentation for verification by testing its compliance with the specified technical requirements in order to make a decision on the possibility of putting into production and (or) use for its intended purpose.
_ [GOST 16504-81, art. eight]
3.1.4 pilot batch: A set of prototypes or a certain volume of non-piece products manufactured for a specified time interval according to the newly developed one and the same documentation to control the conformity of products to specified requirements and make a decision on putting it into production.
3.1.5 design design documentation: design documentation,
executed at the stages of technical proposal, draft and technical projects.
3.1.6 working design documentation: Design documentation executed at the stages of a prototype (pilot batch) of serial (mass) and single production and intended for the manufacture, operation, repair (modernization) and disposal of the product.
3.1.7 design documentation development stage: The finished part of the design documentation development process, consisting of stages of work and characterized by the achievement of a given result.
3.1.8 installation series: The first industrial batch of products manufactured during
mastering production according to the documentation of serial or mass production in order to confirm the readiness of production to release products with the established requirements and in the specified volumes._
3.1.9 data format: The order in which the data symbols are arranged so that their constituent parts can be recognized.
NOTE - The data format takes on a variation depending on the particular set of data symbols, for example the format of the data message.
[GOST 17657-79. Appendix, paragraph 11]
3.2 Abbreviations
The following abbreviations are adopted in this standard:
КД - design documents (documents, documentation);
TK - technical task.
4 Key points
4.1 The stages of design documentation development can be performed in the form of design and working design documentation development.
The stages of development of design documentation and the stages of performance of work established by this standard are shown in Table 1.
Table 1
| Development stage |
Stages of work |
|
| Development of design design documentation |
Development of a technical proposal * " |
Study and analysis of TK |
| Selection of materials |
||
| Development of design documentation for a technical proposal. |
||
| Consideration and approval of the CA of the technical proposal with the assignment of the CA letter VP " |
||
| Development of a draft design |
Development of a draft design |
|
| Manufacturing and testing and / or development and analysis of material layouts (if necessary) and (or) development, analysis of electronic layouts (if necessary) |
||
| Consideration and approval of the design documentation of the draft design with the assignment of the letter "E" to the documents |
||
GOST 2.103-2013
End of table 1
| Development stage |
Stages of work |
|
| Development design |
Development of a technical project |
|
| Production and testing of material layouts (if necessary) and / or development, analysis of electronic layouts (if necessary) |
||
| Consideration and approval of the design documentation of the technical project with the assignment of the design document letter * T " |
||
| Development |
Development of design documentation for a prototype (pilot batch) product |
Development of design documentation. intended for the manufacture and testing of a prototype (pilot batch) of a product, without assigning a letter |
| Manufacturing and preliminary testing of a prototype (pilot batch) product |
||
| Correction of design documentation based on the results of manufacturing and preliminary tests of a prototype (pilot batch) of the product with the assignment of design documentation letter "O" |
||
| Acceptance tests of a prototype (pilot batch) of a product |
||
| Correction of design documentation based on the results of acceptance tests of a prototype (pilot batch) of the product with the assignment of design documentation letter "Oi" |
||
| For a product developed by order of the Ministry of Defense, if necessary, re-manufacturing and testing of a prototype (pilot batch) according to documentation with the letter "Oi" and adjusting the design documentation with the assignment of the letter "Og *. Oz. ... "0" * |
||
| Development of design documentation for a serial (mass) product |
Manufacturing and testing of the installation series according to the documentation with the letter "Oi" (or "Og". "Oj", ... "O n") |
|
| Correction of design documentation based on the results of manufacturing and testing of the installation series, as well as equipping the technological process of manufacturing a product, with the assignment of design documentation letter "A" |
||
| For a product developed by order of the Ministry of Defense, if necessary, the production and testing of the lead (control) series of design documents with the letter "A" and the corresponding correction of the design documents with the assignment of the letter "B" |
||
| Development of design documentation for a single-piece product |
Development of design documentation. intended for the manufacture and testing of the product with the assignment of the letter "I" |
|
| ”Stage“ Technical proposal ”does not apply to CA. developed by order of the Ministry of Defense. Note - All stages of development of a working design documentation may be preceded by the stage of development of a design design document. |
||
4.2 The nomenclature of types of documents developed at each stage of development of design documentation - according to GOST 2.102. if the composition of the documentation is not established in the TOR for development.
4.3 The obligation to complete the development stages and stages of work, the form for submitting the design documentation (paper and (or) electronic) should be established by the developer, if this is not established in the TOR for development.
4.4 If one of the development stages inherent in development work is not completed, the work related to these stages must be carried out at one of the development stages being performed.
4.5 Requirements for the implementation of design documentation must comply with the requirements of the Unified System for Design Documentation.
4.6 The need to develop layouts, their appearance. the conditions and programs of tests (analysis), as well as the need for the development of documentation for the manufacture and testing of models should be established by the developer, if this is not established in the TOR for development. Layouts can be made in material form (material layout) or virtual form (electronic layout). Requirements for the material model according to GOST 2.002. to the electronic model - according to GOST 2.052.
Material layouts should be made, as a rule, according to sketch design documentation. in accordance with
4.7 When performing electronic CA, it is recommended to establish requirements for data formats at a previous stage of development, if this is not established by the TOR.
4.8 When performing electronic CD, the electronic structure of the product and the electronic model of the product (assembly unit, complex, kit) should be performed with a degree of detail corresponding to the development stage. Requirements for the electronic model of the product are in accordance with GOST 2.052. to the electronic structure of the product - according to GOST 2.053.
4.9 Working design documentation for products of a single production may be preceded by the performance of design documentation for individual stages of development (technical proposal, conceptual design, technical design) and, accordingly, the stages of the work indicated in Table 1.
4.10 Technical proposal - a set of project design documentation. which should contain technical and feasibility studies for the feasibility of developing product documentation based on the analysis of technical specifications and various options for possible solutions for products, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products, as well as patent research.
A technical proposal after agreement and approval in the prescribed manner is the basis for the development of a draft (technical) design.
List of works - according to GOST 2.118.
4.11 Draft design - a set of design design documentation. which should contain fundamental design solutions that give a general idea of \u200b\u200bthe purpose, device, principle of operation and overall dimensions of the product being developed, as well as data defining its main parameters.
The draft design, after agreement and approval in the prescribed manner, serves as the basis for the development of a technical design or working design document.
List of works - according to GOST 2.119.
4.12 Technical design is a set of design documentation. which should contain the final technical solutions that give a complete picture of the device under development, and the initial data for the development of a working design documentation.
The technical project, after agreement and approval in the prescribed manner, serves as the basis for the development of a working design document.
List of works - according to GOST 2.120.
4.13 Previously developed design documentation should be used in the development of new or modernization of manufactured products in the following cases:
a) in the project design documentation (technical proposal, draft and technical projects);
b) in the working CD with the letters "O". "O," ("O g", "0 3", ... "O n"), "A", "B" and "I", if the lettering of the document used is the same or higher.
The lettering of the complete set of CD is determined by the lowest of the letters indicated in the CD. included in the kit, except for the CD of purchased products.
4.14 CD. holders of originals of which are other organizations can be used in the organization only if there are registered copies or duplicates of these CDs.
4.15 At the stages of development, "Development of the design documentation" should be developed for the design
At the stages "Development of a working design document", a working design document should be developed.
Working CD. transferred (supplied) to the manufacturing organization for the production of products includes, among other things, operational documentation made in accordance with GOST 2.601. which is then supplied to the consumer (operator) along with the product. The design and working design documentation should be developed at the stage of the product life cycle "Design (development)".
Repair CD. if necessary, it should be developed in accordance with GOST 2.602 at the stage of the product life cycle "Repair", as a rule, after a certain period of operation of the product *.
GOST 2.103-2013
Appendix A (informative)
GOST 2.103-2013
INTERSTATE STANDARD
Unified system for design documentation
DEVELOPMENT STAGES
Unified system for design documentation Stages of designing
For the text of Comparison of GOST 2.103-2013 with GOST 2.103-68, see the link.
- Note from the manufacturer of the database.
____________________________________________________________________
ISS 01.110
OKSTU 0002
Introduction date 2015-07-01
Foreword
Foreword
Goals, basic principles and the main procedure for carrying out work on interstate standardization are established in GOST 1.0-2015 "Interstate standardization system. Basic provisions" and GOST 1.2-2015 "Interstate standardization system. Interstate standards, rules and recommendations for interstate standardization. Rules for development, adoption , updates and cancellations "
Information about the standard
1 DEVELOPED by the Federal State Unitary Enterprise "All-Russian Research Institute of Standardization and Certification in Mechanical Engineering" (VNIINMASH), by the Autonomous Non-Commercial Organization Research Center of CALS-Technologies "Applied Logistics" (ANO Research Center of CALS-Technologies "Applied Logistics")
2 INTRODUCED by the Federal Agency for Technical Regulation and Metrology
3 ACCEPTED by the Interstate Council for Standardization, Metrology and Certification (minutes of November 14, 2013 N 44, Appendix N 24 add.)
Voted for adoption:
Short name of the country according to MK (ISO 3166) 004-97 | Abbreviated name of the national standardization body |
|
Azerbaijan | Azstandard |
|
Ministry of Economy of the Republic of Armenia |
||
Belarus | Gosstandart of the Republic of Belarus |
|
Kazakhstan | Gosstandart of the Republic of Kazakhstan |
|
Kyrgyzstan | Kyrgyzstandard |
|
Moldova-Standard |
||
Rosstandart |
||
Tajikistan | Tajikstandart |
|
Uzbekistan | Uzstandart |
|
Ministry of Economic Development of Ukraine |
4 By order of the Federal Agency for Technical Regulation and Metrology of November 26, 2014 N 1794-st, the interstate standard GOST 2.103-2013 was put into effect as a national standard of the Russian Federation from July 1, 2015.
5 REPLACE GOST 2.103-68
6 EDITION as amended (ISS 7 2015), as amended (ISS 10 2016). December 2018
Information on changes to this standard is published in the annual information index "National Standards", and the text of changes and amendments is published in the monthly information index "National Standards". In case of revision (replacement) or cancellation of this standard, a corresponding notice will be published in the monthly information index "National Standards". Relevant information, notice and texts are also posted in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet (www.gost.ru)
1 area of \u200b\u200buse
This standard specifies the stages of development of design documentation for products of all industries and stages of work.
On the basis of this standard, standards can be developed that take into account the peculiarities of the application of the stages of development of design documentation at various stages of the product life cycle of specific types of equipment, depending on the specifics of their development, production and use.
2 Normative references
This standard uses normative references to the following interstate standards:
GOST 2.002-72 Unified system for design documentation. Requirements for models, layouts and templates used in design
GOST 2.052-2015 Unified system for design documentation. Electronic model of the product. General Provisions
GOST 2.053-2013 Unified system for design documentation. Electronic structure of the product. General Provisions
GOST 2.102-2013 Unified system for design documentation. Types and completeness of design documents
GOST 2.118-2013 Unified system for design documentation. Technical Proposal
GOST 2.119-2013 Unified system for design documentation. Preliminary design
GOST 2.120-2013 Unified system for design documentation. Technical project
GOST 2.125-2008 Unified system for design documentation. Rules for the execution of sketch design documents. General Provisions
GOST 2.601-2013 Unified system for design documentation. Operational documents
GOST 2.602-2013 Unified system for design documentation. Repair documents
Note - When using this standard, it is advisable to check the validity of reference standards in the public information system - on the official website of the Federal Agency for Technical Regulation and Metrology on the Internet or according to the annual information index "National Standards", which was published as of January 1 of the current year, and by releases of the monthly information index "National Standards" for the current year. If the reference standard is replaced (changed), then when using this standard, the replacing (modified) standard should be followed. If the reference standard is canceled without replacement, then the provision in which the reference to it is given applies to the extent not affecting this reference.
3 Terms, definitions and abbreviations
3.1 Terms and definitions
The following terms are used in this standard with the corresponding definitions:
3.1.1
3.1.2 letter: Details of the design document (set of design documents) for the product corresponding to the stage of its development.
3.1.3
3.1.4 pilot batch: A set of prototypes or a certain volume of non-piece products, manufactured for a specified time interval according to the newly developed one and the same documentation to control the compliance of products with specified requirements and make a decision on putting it into production.
3.1.5 project design documentation: Design documentation completed at the stages of a technical proposal, draft and technical design.
3.1.6 working design documentation: Design documentation, executed at the stages of a prototype (pilot batch) of serial (mass) and single production and intended for the manufacture, operation, repair (modernization) and disposal of the product.
3.1.7 stage of development of design documentation: The finished part of the design documentation development process, consisting of stages of work and characterized by the achievement of a given result.
3.1.8 installation series: The first industrial batch of products manufactured during the period of mastering production according to the documentation of serial or mass production in order to confirm the readiness of production to release products with the established requirements and in the specified volumes.
3.1.9
3.2 Abbreviations
The following abbreviations are adopted in this standard:
КД - design documents (documents, documentation);
TK - technical task.
4 Key points
4.1 The stages of design documentation development can be performed in the form of design and working design documentation development. The stages of development of design documentation and the stages of performance of work established by this standard are shown in Table 1.
Table 1
Development stage | Stages of work |
|
Development of design design documentation | Development of a technical proposal | Study and analysis of TK |
Selection of materials |
||
Development of design documentation for a technical proposal |
||
Consideration and approval of the CA of the technical proposal with the assignment of the CA letter "P" |
||
Development of a draft design | Development of a draft design |
|
Manufacturing and testing and / or development and analysis of material layouts (if necessary) and (or) development, analysis of electronic layouts (if necessary) |
||
Consideration and approval of the design documentation of the draft design with the assignment of the letter "E" to the documents |
||
Development of a technical project |
||
Production and testing of material layouts (if necessary) and / or development, analysis of electronic layouts (if necessary) |
||
Consideration and approval of the design documentation of the technical project with the assignment of the design document of the letter "T" |
||
Development of working design documentation | Development of design documentation for a prototype (pilot batch) product | Development of design documentation intended for the manufacture and testing of a prototype (pilot batch) of a product, without assigning a letter |
Manufacturing and preliminary testing of a prototype (pilot batch) product |
||
Correction of design documentation based on the results of manufacturing and preliminary tests of the prototype (pilot batch) of the product with the assignment of design documentation letter "O" |
||
Acceptance tests of a prototype (pilot batch) of a product |
||
Correction of design documentation based on the results of acceptance tests of a prototype (pilot batch) of the product with the assignment of design documentation letter "" |
||
If necessary - re-manufacturing and testing of a prototype (pilot batch) according to the documentation with the letter "" and adjusting the design documentation with the assignment of letters "", "", ... "" |
||
Development of design documentation for a serial (mass) product | Manufacturing and testing of the installation series according to the documentation with the letter "" (or "", "", ... "") |
|
Correction of design documentation based on the results of manufacturing and testing of the installation series, as well as equipping the technological process of manufacturing a product, with the assignment of design documentation letter "A" |
||
For a product developed by order of the Ministry of Defense, if necessary, the production and testing of the lead (control) series of design documents with the letter "A" and the corresponding correction of the design documents with the assignment of the letter "B" |
||
Development of design documentation for a single-piece product | Development of design documentation intended for the manufacture and testing of products with the assignment of the letter "I" |
|
The “Technical Proposal” stage does not apply to design documents developed * by order of the Ministry of Defense. Note - All stages of development of a working design documentation may be preceded by the stage of development of a design design document. |
||
__________
4.2 The nomenclature of types of documents developed at each stage of development of design documentation - in accordance with GOST 2.102, if the composition of the documentation is not established in the TOR for development.
4.3 The obligation to complete the development stages and stages of work, the form for submitting the design documentation (paper and (or) electronic) should be established by the developer, if this is not established in the TOR for development.
4.4 If one of the development stages inherent in development work is not completed, the work related to these stages must be carried out at one of the development stages being performed.
4.5 Requirements for the implementation of design documentation must comply with the requirements of the Unified System for Design Documentation.
4.6 The need to develop layouts, their type, conditions and test (analysis) programs, as well as the need to develop documentation for the manufacture and testing of layouts should be established by the developer, if this is not established in the TOR for development. Layouts can be made in material form (material layout) or virtual form (electronic layout). Requirements for the material model in accordance with GOST 2.002, for the electronic model - in accordance with GOST 2.052.
Material layouts should be made, as a rule, according to sketch design documentation, in accordance with GOST 2.125 *.
_______________
Here and below, the "*" marks the items to which the comments are given in Appendix A.
4.7 When performing electronic CA, it is recommended to establish requirements for data formats at a previous stage of development, if this is not established by the TOR.
4.8 When performing electronic CD, the electronic structure of the product and the electronic model of the product (assembly unit, complex, kit) should be performed with a degree of detail corresponding to the development stage. Requirements for the electronic model of the product - in accordance with GOST 2.052, for the electronic structure of the product - in accordance with GOST 2.053.
4.9 Working design documentation for products of a single production may be preceded by the performance of design documentation for individual stages of development (technical proposal, conceptual design, technical design) and, accordingly, the stages of the work indicated in Table 1.
4.10 Technical proposal - a set of design design documents, which must contain technical and feasibility studies for the feasibility of developing product documentation based on the analysis of technical specifications and various options for possible product solutions, a comparative assessment of solutions taking into account the design and operational features of the developed and existing products, as well as patent research ...
A technical proposal after agreement and approval in the prescribed manner is the basis for the development of a draft (technical) design.
List of works - according to GOST 2.118.
4.11 Draft design - a set of design design documents, which should contain fundamental design solutions that give a general idea of \u200b\u200bthe purpose, device, principle of operation and overall dimensions of the product being developed, as well as data that determine its main parameters.
The draft design, after agreement and approval in the prescribed manner, serves as the basis for the development of a technical design or working design document.
List of works - according to GOST 2.119.
4.12 Technical design - a set of design design documentation, which must contain the final technical solutions that give a complete picture of the device being developed, and the initial data for the development of a working design documentation.
The technical project, after agreement and approval in the prescribed manner, serves as the basis for the development of a working design document.
List of works - according to GOST 2.120.
4.13 Previously developed design documentation should be used in the development of new or modernization of manufactured products in the following cases:
a) in the project design documentation (technical proposal, draft and technical projects);
b) in the working CD with the letters "", "" ("", "", ... ""), "A", "B" and "I", if the lettering of the document used is the same or higher.
The lettering of a complete set of design documents is determined by the lowest of the letters specified in the design documentation included in the kit, except for the design documentation of purchased products.
4.14 CA, the originals of which are held by other organizations, can be used in the organization only if there are registered copies or duplicates of these CAs.
4.15 At the stages of development "Development of the design design documentation" should be developed for the design design document *.
__________
* The text of the document corresponds to the original. - Note from the manufacturer of the database.
At the stages "Development of a working design document", a working design document should be developed.
Working design documentation transferred (supplied) to the manufacturer for the production of products includes, among other things, operational documentation made in accordance with GOST 2.601, which is then supplied to the consumer (operator) along with the product. The design and working design documentation should be developed at the stage of the product life cycle "Design (development)".
Repair design documentation, if necessary, should be developed in accordance with GOST 2.602 at the stage of the product life cycle "Repair", as a rule, after a certain period of product operation *.
Appendix A (reference). Comments on the clauses of the standard
Appendix A
(reference)
4.6 An electronic mock-up is a collection of electronic models of a product that describes its external shape and dimensions, allowing to fully or partially assess its interaction with elements of the production and / or operational environment, which serves to make decisions in the development of a product and the processes of its manufacture and use.
An electronic model is a virtual image of a product or an imitation reproduction of specific properties of a created product or its component part, which allows to fully or partially investigate individual characteristics of the product, as well as to evaluate the correctness of the adopted technical and design solutions.
Material and electronic layouts should be developed:
a) at the stage of developing a technical proposal in order to identify and check options for the main design solutions of the product being developed or its components, analyze various product options, identify additional or clarified requirements for the product;
b) at the stage of development of a draft design in order to check the principles of operation of the product or its component parts, the conditions for placement in the allotted space, the conditions of ergonomics of use and other properties of the product or its component parts;
c) at the stage of development of a technical project in order to check the basic design solutions of the product being developed or its components in terms of spatial-kinematic interaction with other products and component parts with each other and ergonomic conditions;
d) at the stage of developing a working design document for preliminary verification of the feasibility of changing individual components of the manufactured product before making these changes to the working design document of a prototype (pilot batch).
4.15 The life cycle of a product, as a rule, consists of the following stages: marketing research, design (development), manufacturing, control (acceptance), operation, repair, disposal.
UDC 62 (084.11): 006.354 | ||
Key words: design documentation, stages of development, design design documentation, working design documentation, technical proposal, preliminary design, technical project |
||
Electronic text of the document
prepared by Kodeks JSC and verified by:
official publication
M .: Standartinform, 2019