Diy plate feeder. Bird feeders. What can you feed the birds

To make a bird feeder, you need to have a few simple items and tools. The feeder can be made with the children, but keep in mind that you need to follow every step, since during the construction process, sharp things are used - scissors, knives, screwdrivers and even, sometimes, a saw. There are many options for feeders - plywood, plastic bottle, tin can or cardboard.

Here are the most interesting, popular and original ideas for creating a feeder:

Feeder made from scrap materials: toilet paper rolls

You will need:

1 toilet roll

Peanut butter

Small bowl

Plate

A couple of branches

Strong thread or line

Knife (blunt or plastic).

1. Connect the two branches or sticks together using hot glue or string. You can skip this step if you make 4 holes in the bushing (see below).

2. Make holes in the toilet paper sleeve so you can insert two twigs or sticks. Better to make 2 holes: a little higher and 2 a little lower (see image). This item is not required, because the sleeve can be put on differently.

3. Place the peanut butter in a small bowl and use a plastic knife to scrub the butter onto the surface of the cardboard toilet paper roll.

4. Sprinkle the food over the peanut butter-coated sleeve.

5. Repeat steps 3 and 4 for 4 more bushings.

6. Tie a strong thread to the connected branches so that the structure can be hung.

7. Hang all the cardboard sleeves on the branch structure, and then hang everything on the tree.

Plastic bottle feeder. Option 1.

You will need:

Any plastic bottle

Ribbon, thread or line

Awl or drill (for making holes in the bottle and plastic cap)

Bolt and nut

Stationery knife or simple (if necessary)

Deep plastic plate.

1. Prepare a plastic bottle. Remove the label from it, wash well and dry.

2. Make a hole in the middle of the lid and plastic plate.

3. Attach the cover to the plate with a bolt and nut.

4. Make a hole at the bottom of the bottle (bottom).

5. Make a few holes on the side (4-5) at the neck of the bottle to allow the food to spill out when you turn the bottle over. The holes can be made with a clerical knife if the bottle is not too tight.

6. Take the ribbon, fold it in half, and tie the ends into a knot. Pass the tape through the hole at the bottom of the bottle.

Now you can put food into the bottle, screw the cap and turn it over. The tape will allow you to hang the feeder on a branch.

Bird feeder from a plastic bottle. Option 2.

You will need:

Plastic bottle

Plastic container

Strong thread or line

Screwdriver or nail

Knife (simple or clerical).

1. Remove bottle cap and container cap.

2. Place the bottle cap on top of the container cap (center) and trace with a pen, felt-tip pen, or pencil.

3. Using a utility knife, cut a hole in the container lid. The hole can be made slightly smaller than the diameter of the bottle cap.

4. Make one hole at the edges of the container lid.

5. Make a hole in the center of the bottle cap. The hole should be large enough to allow bird feed to flow out.

6. Place the cap on the bottle and then insert the bottle into the opening of the container cap.

7. Tie a strong string to the bottle and put the cap on the container.

Now you can pour food into a bottle or pour water and hang the feeder on a tree.

How to make a feeder out of the box (photo instruction)

Original feeder made of polymer clay

You will need:

Polymer clay

Rope

Thick wire or a piece of aluminum

A baking bowl or any other utensil that can be placed in the oven

A small piece of cloth.

1. First roll out the clay on a flat surface until it is about 6 mm thick.

2. Gently place the rolled clay inside a baking bowl. Trim off excess pieces to keep the clay flat. Make 3 large rope holes in the clay.

3. Place a bowl of clay in the oven. Carefully read the instructions for the clay to know how long it takes for the clay to harden in the oven.

4. When the clay has hardened, carefully remove it from the bowl, tie three pieces of rope to it - tie a knot at one end of each rope, and push the other end into the hole of the clay plate.

5. Tie all ends of the rope and secure with wire.

6. It is advisable to place a small piece of cloth inside the plate so that the birds do not accidentally peck the clay along with the food.

Original pumpkin feeder with your own hands

You will need:

Small pumpkin

Wooden beams (even branches are possible)

Thin wire.

1. Cut off the top of the pumpkin.

2.Use a knife or screwdriver to make 4 holes in the pumpkin for sticks or wooden beams. Make 2 opposite holes at the same height and two opposite holes slightly lower - so you have one branch slightly higher than the other.

3. Take a thin wire and wrap it around each end of the branches so that you can hang the feeder from the tree. Connect all ends of the wire so that the trough can hang straight. Hook them up.

The original idea of \u200b\u200ba bird feeder with your own hands

This feeder is suitable for sub-zero temperatures.

You will need:

Large plastic bottle

Small plastic bottle or small plastic container

Scissors

Coniferous branches

Berries (optional)

Sunflower seeds

1. Cut off the bottom of a large and small plastic bottle. First you can make a hole with a knife and then cut with scissors. You will have the base of the feeder.

2. Place spruce branches, berries and seeds in a circle in the cut out bottom of a large bottle.

3. In the center of the base, place the bottom of a small bottle or small plastic container.

4. Pour dirt, sand or pebbles into a small container.

5. Tie strong string or fishing line to the feeder so it can be hung.

6. If you put the feeder in the freezer overnight, and then remove and remove the plastic parts, you get an ice feeder.

How to make a do-it-yourself feeder using a bottle

You will need:

Small glass or plastic bottle (preferably with a cap)

Small saucer or bottom of a plastic bottle

Wire

Saw (if needed)

Half-ring screw (hook).

1.Use the screws to connect two small pieces of plywood. In this example, the dimensions of the plywood are 11 x 15 cm and 31 x 15 cm.

2. Using the bottle, which you will later attach to the stand, mark the places where you will need to attach two pieces of wire - one at the neck, the other at the bottom of the bottle.

3. The neck of the bottle should be about 3-4 cm above the base.

4. Drill the holes for the wire, push your wire through the bottom, wrap it around the bottle and secure it to the back of the plywood (you can twist the wire or fix it with a stapler).

5. Fill the bottle with seeds, screw on the cap to avoid spilling the seeds, turn over and insert the bottle between the wires, and place a saucer under it and remove the cap.

6. Screw the half-ring screw to the top of the plywood to hang the feeder.

Original do-it-yourself bird feeder

You will need:

Tin can (preferably with a lid)

Sisal rope (sisal rope) or thick rope

A piece of thin plywood, twig, or any small metal piece

Hot glue.

1. If you have a jar with a lid, then the lid must be folded in half.

2. Take a small branch, piece of plywood, or other small piece that birds can sit on and glue it to the jar.

3. Insert the folded lid as shown in the image (slightly inside the can and above the metal part) and secure with adhesive.

4. Take a thick rope or rope about 80 cm long and start wrapping the jar so that at the beginning and at the end there are long ends of this rope (30 cm). Use glue to secure the rope to the jar.

5. Cut the rope, tie the ends into a knot and secure with glue.

You will need:

3/4 cup bird food

1/4 cup water

1 packet of gelatin

Twine or strong thread

Cookie bakeware

Baking paper.

1. Combine gelatin with water (1/4 cup) and bring to a boil, stirring occasionally. Make sure the gelatin is completely dissolved.

2. Remove from heat and let cool.

3. Add 3/4 cup of bird food. You can add more if fits.

4. Place the cookie cutters on the baking paper and fill them with the resulting food mixture.

5. Cut off a piece of thread and tie the ends into a knot. Partially insert the thread into the mixture.

6. Leave the mixture to dry overnight, periodically trying to turn it over when there is time.

7. Remove the molds and hang the food on the tree.

How to make a bird feeder with your own hands using tin cans

You will need:

3 cans of paint or canned food

A piece of twig or wooden stick

Hot glue

Paints (if desired).

You can paint the cans, or you can leave them as they are.

1. Glue a piece of twig to the jar so the birds can land and eat.

2. Wrap a strong thread or tape around the can and tie the ends into a knot. You can attach some glue to the tape so it sticks better to the jar.

3. Fill the cans with food and you're done!

How to make a bird feeder from a plastic bottle

You will need:

Plastic bottle (1.5 L or 5 L) or canister

Sharp scissors or a utility knife

We present to your attention several options for interesting bird feeders made. It turns out that the feeder can be easily made from ordinary plastic bottles, all kinds of boxes, wood - if you wish. This article will try to awaken this desire in you, thanks to which many birds will be able to comfortably survive the winter.

First, let's take a look at the great many different feeders made from a wide variety of materials. This will help you decide on the image, choose the option that suits you.

from a plastic bottle and glass jar

After all, with the help of a tree, the feeder can be given any look: you can build a mini-castle, you can put an ordinary "dining room" on racks, you can decorate the feeder with intricate carvings, etc., as far as imagination allows and there are necessary building materials.

It is very good when children are involved in making - they immediately develop such character traits as caring for their neighbors, love for animals, responsibility, an interest in tinkering, something to create!

Whatever you make your feeder out of, it is important to know the basic (and required) elements of the feeder:

1. Your feeder must be with a roof - this way the food will remain dry and not covered with snow, and it will be easy for the bird to enjoy your treat;
2. Be sure to make the opening of the feeder wide enough, birds are very shy, especially afraid of confined spaces. What if several hungry flyers arrive at your "bird's canteen" for lunch? It is important to take care of this option as well;
3. When choosing a material for a feeder, be guided by its strength and moisture resistance: the denser and more moisture-proof the source material, the longer your feeder will serve;
4. The feeder very often turns out to be too light, therefore it reacts to every gust of wind, while the grains and crumbs are scattered and the birds remain hungry. To cope with this problem, you need to slightly weight the feeder. To do this, lay a piece of plywood, linoleum on its bottom (strictly according to the size of the bottom).

Now you will learn how you can make such a feeder yourself from all kinds of cereals.

This feeder looks great and does a great job at the same time! Branches of trees decorated with such "decorations" give your garden an aesthetic and exclusive look. So let's get started!

We need:

All kinds of grains, crumbs, seeds - all raw, since fried will only harm little flyers;
Egg;
Oatmeal;
Honey;
Gelatin;
Flour;
Pencil;
Thick cardboard;
Scissors;
Dense nylon thread.

1. Using a pencil and a regular sheet of paper, draw the shape of the future feeder. Hearts, stars, triangles, circles, squares - any geometric shapes will look beautiful;
2. Cut a piece of paper with scissors and attach it to heavy cardboard. Circle with a pencil and carefully cut along the contour;
3. Take care of preparing bird feed in advance. Pick up unroasted and unsalted grains, all kinds of bread crumbs;
4. Using a needle and a dense nylon thread, make a hole in the cardboard base and thread a thread through it - with its help this "delicacy" will be attached to a tree branch;
5. To keep the grains and crumbs together and adhere well to the cardboard base, prepare a natural glue:

  • 2 tbsp. spoons of oatmeal (in no case oatmeal);
  • 1 egg;
  • 1 teaspoon of flowing honey;
  • Flour.

All ingredients are thoroughly mixed in a bowl and left for 30 minutes. for swelling.

6. Apply the prepared sticky mass to the base;
7. In another container, thoroughly mix all our grains;
8. Dip and roll in the resulting crumb-grain mixture our base coated with "glue";
9. Ready grain feeders must be placed in the refrigerator for several hours - the mass must freeze well and acquire the necessary strength;
10. Hang such delicious "treats" on the branches of the trees and watch from afar the feast of the birds who have arrived to treat themselves and eat!

Dissolve one packet of gelatin in warm water;
Pour all kinds of grains into the still warm solution;

Send the molds with the contents to the refrigerator to thicken;
Delicious toys are ready, you can safely hang them on the branches of trees!

Another "quick" option is to get some old cups, or take ordinary plastic cups, fill to the top with the prepared mixture (on any basis from the suggested ones). After the mixture thickens in the refrigerator, tie the feeder to the tree branch with a ribbon! The fast option is no worse!

An ordinary cardboard box can successfully serve as a dining room for birds! However, it is advisable to select boxes covered with a special protective layer, laminate - this will significantly increase the life of your feeder!

Juice boxes (both inside and outside are covered with a special moisture-proof layer), from small appliances, medium boxes from postal parcels, bright candy boxes are ideal. Even shoeboxes will do a great job with the functions of a feeder!

Candy Box Bird Feeder

You will need:
Candy box (3 pcs.)
Two medium nylon twine or two shoe laces.

Place one end of the box inside the other so that you get a triangle of three interconnected candy boxes, as shown in the picture:

Pass the string through the roof of the feeder, with the second cord, firmly attach your feeder to the tree.

candy box feeder

The feeder is ready, all that remains is to pour in delicious grains and crumbs!

Even a child can cope with the manufacture of such a feeder (by the way, do not forget to involve children in this entertaining activity).

You will need:
Juice or milk carton;
Long lace;
Knife or scissors.



Take a suitable size box and using scissors or a knife, carefully cut a hole in the side of the box.

Pass the string through the top edge of the box, right in the middle, and attach the "freshly prepared" feeder to the branch.

Get some bird food soon - they've already found a new feeder and are waiting for your treat with all their might!

If you want to make a large enough feeder. To fit a whole flock of birds - take a regular mail parcel box! Carefully glue the top with tape, cut wide holes in the side groans, fix it on a tree - you're done! See what happened:

This is where the soul can turn! There are a lot of all kinds of plastic bottles of various shapes and colors around! There is a great opportunity to show your creativity, invention, originality!

Let's take a closer look at the idea of \u200b\u200bconverting an ordinary plastic water bottle into a FEEDER for birds.

We need:

  • Knife or scissors;
  • Plastic bottle with a capacity of 5-6 liters;
  • Wire;
  • Bird food.

1. Using a knife or sharp scissors, carefully (so as not to cut yourself) cut a wide hole in the plastic bottle, located slightly above the bottom of the bottle (2-3 cm will be quite enough);

2. You can make several windows, one on each side.
3. Wrap the neck of the bottle with a strong wire and secure the other end of the wire to the tree branch;
4. Lay plywood or a piece of linoleum on the bottom of the feeder, with their help we will make our feeder heavier and it will not sway and turn over with every breath of breeze;
5. Fill up the bird food and wait for the "guests" you have invited!

Plastic bottle feeder with spoons

Let's say that you want to make a small compact plastic feeder, then take a plastic bottle of 1.5-2 liters!

You will need the following materials:
1.5-2 liter plastic bottle;
Wire;
A sharp knife or scissors;
Two wooden spoons for coasters;
Bird food.

Step-by-step instruction:
1. Take a plastic bottle with a capacity of 2 liters, measure 15 cm from the bottom of the bottle with a ruler and make a through hole at this height in the very center of the bottle for a wooden spoon;
2. Climb even higher (approximately to the middle of the bottle) and make another through hole for the second spoon. Only at a different angle (perpendicular to the existing holes);
3. Insert through spoon bottle;
4. Increase the hole on the wide side of the spoon - the grains will spill out and it will be convenient for the birds to peck them;
5. Put the bird food into the bottle;
6. Tie a wire around the neck of the bottle and attach it securely to the branches of the tree.
The feeder is ready! In a few minutes, birds will visit it.

Another version of a plastic bottle feeder, more simplified:

We use the same materials as for the spoon trough. But now we don't need spoons, but instead, prepare electrical tape.

So, in a two-liter bottle we cut a large hole at a height of 5-7 cm from the bottom of the bottle. In order for the birds to sit comfortably on the cut edges of the bottle, we glue the sections with electrical tape or tape (of your choice). We wrap the wire around the neck of the bottle and fasten it to the tree branch. Pour in feed - you're done!

DIY wooden bird feeder

We have already considered a lot of different options for bird feeders, made from all kinds of improvised means and even waste. It will not be right at all if a reliable and durable tree feeder is left without attention - these are the feeders that hung on the trees in our childhood. It was them who were taught to make us in labor lessons by our Trudoviks!

Let us recall the manufacturing technology and - let's get started!

First, let's do some fantasy and paint! Armed with a piece of paper and a pencil, draw the type of feeder you plan to make. Seeing her on paper. Estimate the size of the future bird canteen. Only after that you can start making the feeder.

Alternatively, use the ready-made drawings, which are presented at the very beginning of this article. The dimensions are already indicated there, the contours are clearly outlined - you can safely proceed to the next events.

To make a wooden feeder, you will definitely need the following tools:
1. Hacksaw;
2. Hammer;
3. Nails.
Prepare the following materials in advance:
Plywood of the right size;
Bars 2x2 cm;
Thin wooden board for the base of the trough.

We go strictly in size! The dimensions are shown in the drawing.

1. From a thin wooden board (solid) we cut out a rectangular base of the required size;
2. Now go to the plywood sheet and cut out a rectangle of the same size as the base - this plywood sheet will serve as the roof of your feeder;
3. We cut the bar into four parts, and one pair of beams should be 3 cm shorter than the first pair. Thanks to this design, water will flow smoothly along the roof of the trough and will not stagnate on it - the roof will last much longer!
4. We retreat 1-1.5 cm from each end of the trough and nail the racks, first to the base of the trough. And then we nail the roof to the racks. The front struts should be shorter than the rear ones;
5. We nail a wire or a strong nylon cord to the middle of the roof and fix the feeder to the tree.
All! The work is done, we pour the food, and we admire the fun bird feast! Do not forget to take pictures - the memory will remain for life. There will be something to show to grandchildren and what to make together with them!
In no case do we paint the feeder with paint or varnish - birds do not tolerate such odors and will not visit a painted feeder with their presence!

What food is good for birds, and what, on the contrary, can harm them?
Feeding birds is a commendable activity, but you should know that not all food is suitable for birds! One food can provoke the illness of a trusting and hungry flyer, another can even lead to the death of the bird, but the third one will definitely help the bird to hold out in the cold and hungry bench press and live until the long-awaited spring!

So, what should not be given to birds in feed:

  • Fresh white bread crumbs;
  • Rye bread crumbs;
    Banana skins and all kinds of citrus fruits;
    Cream cakes, cakes;
    Chips;
    Roasted and salted seeds;
    Oat flakes;
    Nuts.

What can and should be treated to birds:

  • Raw seeds;
  • Buckwheat, millet, oats, millet;
  • Crumbs and small pieces of stale white rolls;
  • Dried and cut into pieces fruits (dried fruits);
  • Titmouses are very fond of small cubes of unsalted bacon;
  • For red-sided bullfinches, put mountain ash, viburnum in the feeder.

A few more photos of the original feeders:

Thanks to your attention and care in the winter, there will be a real chance to survive for a larger number of birds, which in turn will certainly thank you later with their songs and "sanitary and health" work in your garden!

Watch also the video: DIY bird feeder in 10 minutes.

Birds are our lesser friends who delight us with their chirping and singing. And any garden in the presence of birds seems to come to life, filled with new life. Also birds help to protect the summer cottage from attacks of various insects in the summer... And in winter, when they have almost no food, a person's task is to help the birds survive the frosts by feeding them. A good attitude towards birds will pay off handsomely. for birds with their own hands it is done quickly, without unnecessary manipulation, it will not only become a source of food for birds, but it will also be able to decorate any site.

Feeders for winged birds were made by many while at school, and someone together with their parents managed to make far more than one feeder while still attending kindergarten. At that time, tasks for making feeders were given at school in order to instill in the child the desire to work and take care of our smaller brothers.

Now, in most cases, the feeders on the house plots are located in order to lure the birds to permanent residence in the garden or to take care of them in the winter. There are a great many variations of feeders, but do not forget that if a person is pursuing a good goal, he must make sure that the feeder is not just beautiful, but comfortable and attractive for birds.

So what should it be so that birds from all over the area flock to nibble on delicious treats?

  1. The feeder shouldn't be bright... Do not forget that birds are inhabitants of the wild, in which bright colors often indicate the danger of any insect or animal. So it is unlikely that birds will fly to the feeders of nuclear flowers. The best option is the color of the wood.
  2. The feeding area should be equipped with small sidesso that food does not fall out of it during the wind and at the moment when the bird lands on the feeder and shakes it.

  3. It is important to make sure that the sides and other elements of the feeder are not sharp and do not pose a danger to birds.
  4. The best thing, so that the trough has a small roof - then the food lying in it will not get wet in the rain, and it will not be covered with snow.
  5. It is recommended to place the feeder where cats and other predators cannot reach it.... Then the birds will happily fly to her. If the place is dangerous, then it is unlikely that it will be possible to lure the birds.

  6. All openings in the walls of the trough should be spaciousto avoid creating a confined space effect. Otherwise, the birds will be uncomfortable.
  7. It is best to design a feeding area that will withstand various weather conditions and will not collapse after the first season.
  8. The feed in the trough must be clearly visible - Birds use more sight than other senses when looking for food.

Advice! In order to make the structure heavier and protect it from swaying in the wind, you can place pebbles in it, but so that they do not end up in food.

Which is better: homemade or from a store?

You can make a place for eating birds yourself, but stores now sell ready-made structures and products that you can simply purchase and hang in your garden or outside your window. Of course, then a lot of time is saved, but it is better to make the feeder yourself or order it from the masters. Only in this case, you can be sure that the feeder is made of materials that are safe for flying inhabitants of nature and will correctly perform its function.

On a note! Undoubtedly, you need to pay attention to the design of the feeder, but if this is not just a decorative decoration of the garden, then, first of all, you should pay attention to its functionality.

It is also important to understand that a good, but made in production or by craftsmen feeder will cost a lot of money. So it is worth thinking about what to do - to save money and do everything yourself, or still spend money and buy a ready-made version.

Provided that the actual feeding area can be made quickly and easily, the DIY option remains the best. The main thing is to decide and decide from what and how to make a feeder, how and where it will hang, and also take into account the availability of skills in making various products. You shouldn't take on a complex project without proper experience, it's easier to choose the simplest option. Fortunately, there are many types of feeders.

Table. Types of feeders.

ViewDescription

This category includes all types of feeders that are fixed in place by hanging. Such a structure will most likely require weighting to prevent it from swaying in the wind and during the landing of birds. This category also includes simple feeders with lard or grains stuck together in one lump. They are suspended from trees on a braid.

The most familiar, familiar from childhood and widespread option. The roof of such a product is made in the form of a house, it protects the food from getting wet. It is best if the roof is installed on thin blocks so that there is as much free space for birds as possible.

Such a feeder is a board with sides, suspended on something. It does not have a roof, and therefore the food will constantly get wet or covered with snow. But this is the easiest option.

Such a feeder is a small bunker container with feed inside. The birds, pecking at the food that has spilled out on the pallet, make room for a new one, which is gradually poured out of the bunker. Also, in some cases, birds can peck grain directly from the bin. The main advantage is good protection of the feed from water and wind.

A feeder designed for stubblers. Often sold in stores. It must be periodically cleaned of debris, as the birds will leave it behind themselves and food in large quantities.

On a note! The structure can be made simply from feed by combining the grains into a single lump using various nutrients and hanging such a "gingerbread" in a conspicuous place. Suitable for small birds that will peck grain from the feeder, clinging to it with their claws.

What can you make a feeder from?

You can make a feeder yourself from a variety of objects and materials, ranging from a regular board to a plastic bottle or even a tetrapak box. Each material has its own advantages and disadvantages, and it is necessary to choose what the food supply will be made of, based on the presence of certain skills in working with various tools, the availability of free time, funds, and also the goals of creating a place for eating.

Wood feeders

The best option for creating a feeding area for birds was and remains a natural, unprocessed tree. This design will be closest to nature, and its neutral color and smell will not scare birds away from food. Ideally, if the natural bark is preserved on the boards. So when choosing a material, you can stop at the cuts of birches, pine, etc. You can even make a feeder from branches!

Wooden feeder is the best option

But in order to make a wooden, even the simplest feeder, you will need certain skills and tools for working with wood.

Advice! You should not decorate the wooden feeder with various bright objects, but you can decorate it with natural material, for example, disguising the roof with twigs, cones, leaves.

How to make a tree feeder?

Consider how you can make the simplest wooden feeder. To do this, you need to buy wooden blocks, a small piece of fiberboard, a furniture stapler, a saw, drawing supplies and a tape measure.

Step 1. A square or rectangle must be cut out of a fiberboard sheet. A drawing of a square or rectangle of the appropriate size should be applied to a fiberboard sheet, and then cut off the excess with a saw.

Step 2. Now you need to make the sides for the pallet. It is necessary to cut from the bar two pieces of the same length, equal to the side of the square or the long side of the rectangle, as well as two shorter pieces, which will be equal to the width of the square or the narrow side of the rectangle minus the thickness of the bar.

Step 3. The sides must be attached to the bottom of the trough, which was previously made of fiberboard. The easiest way to do this is with a stapler.

Step 4. Now you need to make 4 supports for the roof of the feeder, all from the same bar. They must be the same height.

Step 6. The upper parts of the supports standing on one side must be connected with crossbars cut from the same bar. You should also make cuts on them at an angle of 45 degrees.

Step 7. Further it is made. It is required to connect two sheets of fiberboard at an angle of 90 degrees. The connection is made using a small "ridge" bar with a length equal to the length of the ramp. It is worth remembering that the roof should slightly hang over the feeder pan, which means that the slopes should be made with this factor in mind.

Step 8. Next, the roof must be fixed on the racks for it using the same stapler or nails. The joint of two slopes can be glued using any material that does not allow water to pass through. The feeder is ready. If desired, you can steal it with cones and branches.

Advice! While fixing the sides at the bottom of the trough, they can be additionally coated with PVA glue to ensure the connection not only due to stapler staples, but also due to glue.

Peeling birds are most fond of feeders with sides, and for the rest you can make a feeder without sides. The main thing is that the side is not too high.

Similar structures can be made from plywood, abandoning the use of fiberboard. In this case, the trough will be more reliable and durable.

Video - Wood feeder

Simple hanging feeders

These are very simple feeders, they can be easily and simply made in just a few minutes. They represent a delicacy placed on a braid or in a case and suspended from a tree. Often, according to this principle, pieces of fat for tits are fixed on trees. You can also make balls from seeds. You can use peanut butter or lard to hold the grains together. And such feeders just need to be fixed on the braid somewhere in a place visible to birds. To attract attention, you can try to tie a rowan branch to such a feeder. You need to form balls on the street so that they immediately freeze in the cold.

Advice! It is best to make suspensions in the shape of a ball, and not in some beautiful and exotic shape. It is the ball that is the most convenient option for birds.

Making a lard feeder

Let's see how you can make a simple structure for placing bacon, for the manufacture of which you will need twine, wire and ordinary hoops - an accessory for embroiderers.

Step 1. In the store you need to buy a regular plastic hoop. They need to be split into two halves, but the hoop should remain connected in the lock area.

Step 2. In the lock area, wire the hoop on both sides with wire.

Step 3. On the other hand, where the hoop is separated, you need to make a jumper wire and wind it with a “tail” from the wire to about the middle.

Step 4. The remaining wire must be twisted and formed into a hook at an angle of 90 degrees, which is directed towards the inside of the hoop. Fat will sit on it.

Step 6. After that, the hoop and wire must be wrapped with ordinary twine. The feeder is ready. It remains to place it in the right place in the garden and put a treat for birds on the pin.

Making a feeder from a plastic bottle

Of course, you can simply cut a hole in the wall of a plastic bottle and hang it from a tree, filling it with grain. But you can contrive and make the feeder a little more complicated. To do this, you need pallets for flowers of different diameters and a plastic bottle of about 1.5 liters. A sturdy rope is also useful.

Step 1. In one of the pallets (which is smaller), you need to make a hole of the same diameter as the bottle neck. You can cut it with a knife or a special crown worn on a drill.

Step 2. Next, you need to remove the cap from the plastic bottle and screw the bottle itself with the neck into the pallet, and screw the cork onto the neck from below. But for now, the structure can be temporarily disassembled. A small hole should be cut in the side of the bottle so that food can spill out of it and be available to birds.

Step 3. The bottom of the bottle must be cut off with a sharp knife.

Step 4. Now on the pallet - both on the first and on the second - you need to outline and drill holes for the rope. First you need to make holes on the smaller one, and then, attaching it to the larger one, mark it and drill the holes too.

Step 5. The final assembly of the structure is carried out. The bottle must be screwed to the bottom tray.

Step 6. You need to cut six pieces of rope of equal length. It is better to take a rope that is dense and thick enough. You can also use a synthetic version.

Step 7. Now on each rope you need to tie a knot at the same distance from the edge.

Step 8. It is required to thread the ropes through the holes on the small pallet so that the short tails of the ropes are at the bottom.

Step 9. The second pallet will become a makeshift roof for the feeder. Now you need to thread the ropes through the holes of the second pallet.

Step 10. The ropes need to be tight. You should get the same construction as in the picture.

Step 11. Now it is required to form "tails" from the top and bottom of the rope remnants. On the upper side, do not forget to make a hanging loop.

Step 12. It remains only to fill the feeder with seeds and fix it on the tree branches using the hanging loop.

Video - Feeder from a plastic large bottle

Video - Glass bottle bunker feeder

You can make bird feeders from any materials. In haste, a feeding place can be built even out of cardboard, but such a feeder will not last long. If you want to decorate the garden with beautiful and durable feeding places for birds, then it is better to spend your time and make a tree feeder.

In today's article we will look at the topic - how to make do-it-yourself bird feeders. Photos, original ideas, you can take note of. Don't forget to bookmark the link to the article about feeders.

The birds may die, not survive the cold winter. Another reason for their death may be lack of food. Feeding birds is an important and noble cause. In addition, hand-made feeders will successfully fit into the atmosphere of your personal plot and decorate its territory. Feathered friends, in turn, will help you in the fight against pests, thereby preserving your harvest.


Don't limit your imagination. The feeder can be made of any materials, the main thing is to make it reliable and durable. But don't forget about safety. The bird hole can be treated with resin and duct tape to protect feathered guests from injury and cuts.



The birdhouse should be located in a convenient location. Do not hang it in an area thickened with trees, in places of strong drafts, as well as where cats are walking. Place the birdhouse in an open, viewable area, and feathered friends will immediately notice their home.



You can do the exciting business of creating a birdhouse with your children and take your creation to school, kindergarten. They will love the creative activity and have fun together!

How to make a bird feeder from a 5 liter plastic bottle

This craft is easy to do. Your child is already in 1st or 2nd grade, he can easily cope with this task.

Prepare the following items:

  • screwdriver;
  • rope;
  • plastic bottle;
  • scissors (office knife);
  • pliers.

Work process:

  1. We cut out windows on each side of the bottle. To do this, make 3 cuts, the underside of the door must remain intact.
  2. Bend the door down with pliers. It turns out a platform for birds, where they will land for food.
  3. Remove the cap from the bottle and make a hole in it with a screwdriver.
  4. Preparing the rope. Fold it in half (if required, repeat the procedure) and push it into the gap made in the lid. Tie a knot at the end of the rope and screw in the lid.
  5. We fill in the seeds and hang the finished product.




DIY bird feeders - original ideas

The feeder can be built from any material at hand, even from the seemingly most unexpected. For example, from toilet paper rolls.

From toilet paper rolls

To make it, we need:

  • peanut butter;
  • rope;
  • knife;
  • cardboard sleeves;
  • branches;
  • plate;
  • birdseed.

Manufacturing process:

We take a couple of branches and fasten them with hot glue. You can connect them by tying them with a rope. And also another option is possible. Just punch 4 holes in the cardboard sleeve to fit the branches (2 higher and 2 slightly lower). Choose for yourself any of these methods of fastening branches.

  1. Apply the peanut butter to the cardboard sleeve using a knife.
  2. We dip the sleeve into the feed.
  3. Repeat steps 2 and 3 for the rest of the bushings.

We tie a rope to the branches and hang the structure.



Original pumpkin ideas

The original tank with poultry food can be made even from pumpkin.

For this we need:

  • wire;
  • wooden sticks;
  • screwdriver:
  • pumpkin.

Manufacturing procedure:

  1. Cut off the top of the pumpkin and remove the pulp from it.
  2. With a screwdriver, make 4 slots in it for wooden sticks (2 higher and 2 lower, the sticks will be located at different levels).
  3. We take a wire and wrap each end of the sticks with it, then it will be convenient to hang the pumpkin on a branch. We connect the wire, hang the pumpkin evenly, you can twist it with a crochet hook.





With a little ingenuity, make an excellent feeder, perhaps even from an old log.

You just need to cut the core, free space is formed for food and feathered guests. The main thing is to choose a solid suspension. A chain is fine for this. It will reliably withstand the structure and look beautiful.



From old dishes

Are there old dishes? From it, you can also make an original shelter for birds. And at the same time you will be able to decorate your garden with such an interesting solution. Simply glue the cup and saucer together and position the structure on the branch, attaching any pendant.

You can build a tiered pyramid using a plate, saucer, and cup. The plate should be on the lower level and the saucer slightly higher. Then you will have a feeder and drinker. You can choose a decorative chain as a fastener.

From ice cream sticks

Do you like popsicle? Do not rush to throw away the wooden sticks from it. After all, an interesting version of the feeder can be constructed from them.

Prepare:

  • rope;
  • popsicle sticks;
  • glue.

We start the manufacturing process:

We lay out the sticks one after another in one row.

  1. We fasten two sticks on opposite sides with glue so that the row does not fall apart. Then we repeat the procedure from the reverse side.
  2. We build a fence of sticks and fasten them with glue. A large stick can be placed at the bottom of the structure. It will serve as a perch.
  3. We pass the rope and the craft is ready! It can be painted in any color you want.



Original feeder made of polymer clay

To make such an unusual polymer clay feeder, take:

  • a piece of fabric;
  • rope;
  • wire;
  • cookware that can withstand the heat in the oven;
  • polymer clay.

Work process:

  1. Roll out the clay on the table. The layer should be 6 millimeters thick.
  2. We place the clay in the dishes, which we will send to the oven. We cut off all unnecessary, forming smooth edges. We make 3 large holes into which the rope will be inserted.
  3. We send the dishes to the oven. Pre-read the instructions for using the clay, correctly timing its baking in the oven.
  4. We take the hardened form out of the plate and tie 3 pieces of rope to it. We tie knots at the ends of each segment. The other ends should be threaded through the holes.
  5. We connect the pieces of rope with a wire or an aluminum piece.

Put a small piece of material inside the plate, the birds will not be able to peck on the clay bowl, being carried away by absorbing food.

From coconut

Coconut can be a great bird food. The main thing is to make the door in a strong shell. Only an adult can cope with this, using a special tool.

Once the hole is drilled, the pulp must be removed from the coconut. The rope hole is much easier to make.

We push the end of the rope into the hole made in the upper part of the nut and make a knot.

We hang a nut on a tree and fill it with seeds. If you drill a smaller door, then it is quite possible that the birds will find their warm home and settle in it. It turns out to be a wonderful dining room and hotel room for our little friends.



You don't have to get the coconut pulp. The birds themselves will cope with this task quite successfully!

Jar feeders

Do you have metal cans lying around at home and at your dacha? They can go into action. After all, they are a fairly durable material.

Let's start making the feeder:

  1. Take cans, paint, colored tape, glue, and wood sticks.
  2. Paint the cans in bright hues to attract birds to eat.
  3. Tie the jars with tape and hang them from a branch. From the bottom, fix the stick with glue, it will be convenient for the birds to peck at the food.



You can cook a treat for the birds yourself by making a kind of kozinaka. You can cook a culinary miracle pretty quickly. Eating such a treat, the birds will peck the food slowly and carefully and will not be able to scatter it.

For cooking, take:

  • 2 packs of gelatin;
  • cocktail tubes;
  • cookie cutters;
  • any seeds (buckwheat, sunflower seeds, rolled oats, millet, dried fruits);
  • thread or rope;
  • hot water (2/3 cup).

Cooking process:

  1. Pour boiling water over the gelatin, add the food and mix the mixture well.
  2. We spread the resulting mass into molds and insert the tubes from above.
  3. When the mixture has cooled, take out the tube and take out the mass from the mold. Pull the rope into the hole from under the tube.

Birds can peck food even from a cone. Find a larger cone in the forest and coat it with peanut butter. Various grains will stick well to it.

Make an edible garland and place it on the tree. Slide the cornflakes over the wire and form into hearts. In turn, they need to be fastened together, and then hung on a branch.



DIY wooden feeder with drawings and dimensions

Wooden feeders are durable, environmentally friendly and functional. Birds can cling to the sides and settle down comfortably to peck food. The most suitable side height is 4 centimeters.

Thin plywood is suitable for the bottom and roof, and wooden blocks are suitable for the manufacture of vertical elements. The height of the feeder is considered optimal from 20 to 30 centimeters, and the length of the sides is from 25 to 40 centimeters. The roof should not be plastic, metal, so the birds that have flown in will not slide off it.

The feeder is hung on a rope and tied to a branch, and also attached to the trunk and to the fence. Please note that it should be convenient to replenish feed stocks.

To make a product, we need:

  • roulette;
  • plywood, boards, wooden blocks;
  • sandpaper;
  • pencil;
  • hacksaw;
  • drill, screwdriver or hammer;
  • drills, screws or nails;
  • glue;
  • carpentry corner.

You can find various schemes of bird feeders on the Internet. In our example, we will use a blueprint.

Work process:

  1. We outline the markings with a pencil and cut out the details along the lines.
  2. We attach the bars to the bottom with self-tapping screws. They function as bumpers. On the short side, we fix the bars end-to-end with the edges. On the long side, we indent about 5 millimeters.
  3. We fasten the walls with self-tapping screws to the long sides with indents.
  4. We fix the walls by connecting them together with a bar, which we fasten with self-tapping screws from the inside.

We pass the rope through the top of the roof and hang the tree house.

Be sure to sand the wooden parts with sandpaper, the bird will not get hurt. A house assembled with self-tapping screws is stronger than a structure fastened with nails.

Below are the assembly diagrams with and without side walls.







Feeder with your own hands from a box for juice in kindergarten

Even a child can easily make a birdhouse from a box of juice and milk. You can bring such a craft to the kindergarten.

For her, we need to prepare:

  • scissors (office knife);
  • felt-tip pen;
  • an empty box;
  • electrical tape;
  • awl;
  • rope or wire.

First, we outline the markup and cut out a window in the wall of the box. We do the same on the opposite wall, the birds will be able to freely fly in and out after a meal. We bypass the holes with electrical tape for safety reasons. Then we bend the corners of the bag and make holes in them with scissors and an awl. We will put the rope in them.

To prevent the house from swaying from the wind, it can be fixed on a tree trunk. In this case, the windows are best done on the adjacent walls of the box. We make holes on the opposite wall, insert the wire and attach it to the trunk.



Two juice boxes also make an excellent feeder. Cut one box in half along the narrow side, leaving the top intact. We use only half or one third of the second package. It will serve as a bottom. We make a window on one of its sides. Feed will be poured there. We combine the boxes and we get a triangle shape. It can be glued or tapered. And also poke holes at the bottom and thread tubes through them.

You can build a huge number of options for bird feeders with your own hands.





Photos, original ideas for their manufacture, we have considered in this article. Using these easy instructions, you will be able to make any bird house with the kids. Wish you luck! Subscribe to the blog and share master classes with your friends on social networks.

Best regards, Natalia Krasnova.



Bird feeders can be seen in courtyards and parks. If you want to design something special, extraordinary, then we will tell you how to make a bird feeder yourself.

An easy way to feed the birds

The feeder can be made from improvised means, for example, take a piece of board, plywood or any flat and durable material at hand and perpend it higher from the ground. This will keep the feed available to the birds.

This is a temporary measure, as precipitation may fall or the food will simply be blown away by the wind. But such a feeder can save birds from starvation.

We use plastic bottles

From a plastic bottle, you can build both a very simple and a multifunctional dining room for birds. Let's consider in more detail some of the ideas of the feeders, and their implementation.

Hastily

If you cut a hole in the side of the bottle, then we can say that we have done half the work. Near the neck, you need to make 2 holes with an awl, insert the wire and fix the feeder on a branch of a tree or bush. If you put food on the bottom, after a while you can see how birds flock there.

To prevent moisture from spoiling the food when sediment gets inside the bottle, drainage holes need to be made in the lower part of the container.

Complicating the design

From a plastic bottle, you can make a feeder with a "delivery window". Having picked up a container of a suitable size, cut a small hole on one side, and pierce the bottle with scissors on the opposite side. Insert the wooden spoon with the handle first so that it fits snugly into the pierced hole. The spoon must be positioned so that the grains roll into it as the birds peck at the food. The number of spoons involved may vary, but most often there are two.

To hang the bottle, you can pierce the cork with an awl (or nail), thread a nylon thread through it, and tie a knot inside the cork.

How to decorate a gray, unsightly bottle? If you wish, you can make the feeder a decoration of any garden.

Glass feeder

You can make a simple structure from a plastic bottle, which will be attached directly to the glass using suction cups. The device of such a feeder is very simple, and for its manufacture you will need only 1 container and 2 suction cups.

A small square or rectangular hole is made with a construction knife. With a soldering iron or a gas-hot nail on one side of the bottle, you need to make 2 holes into which the suction cup heads will fit tightly. In our case, the suction cups were with hooks, so we first removed them, and then fixed them with them, inserting them into their places, but already inside the bottle.

The positive aspects include the fact that the birds can be watched, almost close to them. A significant disadvantage is that birds defecate near the feeder, so the glass and ebb will look unsightly.

Video: making a feeder from a plastic bottle

Glass use

Glassware can be used to distribute food to birds. The container must be securely fastened down with its neck at a short distance from any platform. Pour the food into this container and replace it (holding the hole with your finger to prevent the grains from spilling out). As the feed is consumed, what is in the bottle will flow to the site.

Video: glass feeder

Other materials at hand

It will not be difficult to come up with a lot of ways with which you can feed the birds.

Tits love not only grains. You can feed such gourmets by hanging a piece of unsalted bacon wrapped in rope or wire on a branch.

If you buy products packaged in nets in supermarkets, then this container can also be used by pouring nuts into it.

You can mold a ball from a fine bulk feed (adding flour and water) and also hang it in a net. In frosty weather, the food can be mixed with vegetable oil. Milk or sour cream is not suitable for these purposes, since the bird's body does not accept such food.

In order to protect the feed from rainfall, a plywood roof can be built.

Pumpkin

The pumpkin feeder can be called waste-free production, since the birds first eat the feed, and then the edible "canteen" itself. It is enough to cut holes in the pumpkin and pull out the core.

You can cut the pumpkin in half, thread a rope through both halves with a knot tied at the bottom. To fix it in a disconnected state, you need to install spacers from branches between the halves. In extreme cases, you can use pencils as supports. The top edge of the rope threaded through the pumpkin is tied to a branch, and the feeder is ready to receive feathered guests.

Video: pumpkin feeder

Spring from the sofa

Things and objects can be used that usually have nowhere else to apply.

If you still have a spring from an old sofa, then you can also use it by holding pieces of bread between the loops. This feeder can be hung both vertically and horizontally.

Car air filter

A metal mesh feeder can be seen on the store counter, but a similar structure can be built from an old paper car air filter.

For manufacturing, you need to cut off the upper part of the filter, and remove the paper filling (you can together with the inner or outer mesh, if you do not plan to fill the food between them). Outside the filter, a wire is tied to the top of the mesh, which will serve as a loop for hanging the feeder on a tree. Suitable food is poured inside, and the cut off top of the filter can be used as a lid.

To reduce feed loss, you can glue a plastic bucket lid to the bottom of the trough with hot glue. A canopy can be made from the same cover.

Teapot

If you have an old kettle and it is a pity to throw it away, but you can no longer use it for its intended purpose, then you can make a feeder out of it. How to hang it? Drilling a hole in a faience product is a very thankless task, so you can use hot melt glue. If there is a hole in the lid, then you need to push the ends of the rope into it and make a knot inside. Tie a small puck as a safety net. The lid can now be glued to the teapot, the neck of which will now serve as an entrance for the birds.

Looking into a shed or pantry, you can find things that are "hard to carry, but sorry to leave." These include the old metal bread bin. Great imagination is not required to place it - I tied a rope and hung it on a branch.

Likewise, an unnecessary plastic container can be used.

Using different boxes

It will also be easy to make a feeder out of a juice or wine box.

One or two windows are cut out in the box so that there is a small bowl for food at the bottom.

When cutting out the window, care can be taken to protect the feed from precipitation. To do this, a small visor is left, but so that it does not go down and close the entrance, it can be fixed with a nylon thread in the open position.

To make a large cardboard feeder, you need a large box. A window of the required size is cut out with a construction knife or scissors. If the box is very large, then a smaller product can be cut out of it and wrapped with tape. It is important to realize that such a feeder will only last until the first rain.

Tin box

Often, manufacturers sell products in tin boxes, which can also be used to make feeders.

In addition to the bank itself, we need:

  • metal or plastic chain - 2 m (4 pieces of 0.5 m each);
  • split ring (used for keys);
  • small cotter pin - 8 pcs. (you can do with knitting wire);
  • awl;
  • alcohol marker;
  • nippers or scissors for metal;
  • ruler;
  • pliers.

Now let's start making.

  • As accurately as possible, you need to mark 4 points on the jar and transfer the same marks to the lid.
  • According to the marks, you need to make holes with an awl so that a cotter pin passes through them.

  • Using pliers, cut the chain into four pieces of 50 cm each.
  • Having passed the cotter pin through the extreme link of the chain, insert it into the hole and, from the inside of the can, push the ends apart with pliers.

  • Having measured 15 cm of the chain (starting from the can), we will thread the remaining 4 cotter pins into it and fix the lid with them.
  • Now we will pass a split ring into the ears of the free ends of the chain.

After hanging the feeder on a branch, look in which direction the box slopes, and in the bottom (from the inside) pierce it with an awl - this will be a drainage hole.

Branches

From large branches, you can assemble an original feeder. To get the job done, you need an ax, a hammer, nails and a little imagination.

Plywood

Plywood products are strong enough, but they are afraid of moisture.

A simple version of the trough consists of just a pallet with sides, two pieces of plywood that serve as a roof, and a rope that connects all parts. To fix the bottom and roof in the desired position, knots are tied on a rope.

If there is a desire and a jigsaw, then you can design a more complex feeder using one of the presented drawings.

Log

When preparing firewood, logs with a rotten core are encountered. This piece of the trunk will serve as a base for us. Need to get the core out. Windows are drilled in the hollow trunk or its longitudinal part is cut out. The ends are closed with selected "plaques" sawn off from other trunks. A tree trunk feeder can be found both horizontally and vertically.

For manufacturing you will need:

  • self-tapping screws;
  • small nails;
  • reiki.

For the manufacture of the roof and bottom, you can use plastic or MDF (which you can find, since this material is sold only in large sheets).

In the manufacture of any design, it is convenient and practical to use the drawings, which indicate the dimensions of the parts. We will also use the drawing in order to cut out all the blanks to size.

They can be lightly sanded.

First, we will assemble the narrower part of the future feeder, hammering 3 nails on each side.

Then the entire frame is assembled in a similar way. If the nails are short, then 5 pieces can be used.

We install the frame on the prepared bottom and outline it outside with a pencil - this way we get the markings along which it will be necessary to cut out this part, and then nail it.

In order to fix the upper rails, we use 4 self-tapping screws - 1 pc. for each attachment point.

From the remaining rails we will make the upper part of the feeder, fastening the parts with self-tapping screws. The final stage will be marking, cutting and fixing the roof. The joint of two roof sheathing sheets can be hidden by nailing a corner rail on top.

There are some points to consider when making and determining the location of the feeder installation:

  1. Do not underestimate cats, because they can get to the feeder, and then the birds will fly away or become the prey of a domestic predator.
  2. The feeder must be made with a large roof, then a lot of precipitation will not fall into it.
  3. The entrance to the feeder should not be small, as fear can be stronger than hunger and birds may not take advantage of your hospitality.
  4. It is better to make the structure of a moisture-resistant material, then it will last a long time. Other materials must be treated with water-repellent compounds.
  5. If the feeder is too light or has a large windage, then a gust of wind can turn it upside down. Even short-term overturning will result in all feed being on the ground. A lightweight structure needs to be heavier.

Photos of original feeders

Video: original ideas brought to life

Drawings and sketches